MCQ Questions
🔍 Search
Menu

Electricity and Magnetism Practice — MCQs with Answers (Set 4)

Practise 25 questions on Electricity and Magnetism.

0 / 25 correct · click an option to check it

Q1. A permanent magnet repels which type of substance placed near it?

Show answer and explanation

Answer: B

Only diamagnetic substances are weakly repelled by a magnet. Paramagnetic substances are instead weakly attracted, and ferromagnetic substances are strongly attracted.

Q2. Regarding a bar magnet’s poles, which statement is correct?

Show answer and explanation

Answer: A

Cutting a bar magnet never isolates a single pole — it always produces two new, complete magnets, since a North and South pole must always exist together, with exactly equal strength.

Q3. Assertion (A): It is not necessary for every bar magnet to have exactly one North pole and one South pole. Reason (R): Magnetic poles always occur in pairs. Which is correct?

Show answer and explanation

Answer: D

Every bar magnet does have exactly one North and one South pole, making Assertion A false. Reason R, however, is a true and fundamental fact — magnetic poles always occur in inseparable pairs.

Q4. If a bar magnet is cut into two equal halves, what happens to the pole strength of each resulting piece?

Show answer and explanation

Answer: D

Since magnetic monopoles don’t exist, each half becomes a complete new magnet with its own North and South pole, retaining the same pole strength as the original.

Q5. If the speed of a magnet moving inside a coil increases, what happens to the induced current in the coil?

Show answer and explanation

Answer: A

A faster-moving magnet changes the magnetic flux through the coil more rapidly, and Faraday’s Law says a faster rate of flux change induces a larger current.

Q6. Two long, parallel wires each carry current in the same direction, placed close together. What happens between them?

Show answer and explanation

Answer: A

Currents flowing in the same direction through nearby parallel wires attract each other, while currents flowing in opposite directions repel — a direct consequence of each wire’s own magnetic field.

Q7. In Fleming’s Left Hand Rule, which finger represents the direction of the electric current?

Show answer and explanation

Answer: C

The standard convention assigns the thumb to force, the index finger to the magnetic field, and specifically the middle finger to current — often remembered as the ‘FBI’ rule.

Q8. Fleming’s Left Hand Rule is specifically used to find the direction of?

Show answer and explanation

Answer: A

Fleming’s Left Hand Rule, often called the motor rule, predicts the direction of the force on a current-carrying wire placed in a magnetic field.

Q9. How much time separates successive direction reversals in a sinusoidal 50 Hz current?

Show answer and explanation

Answer: C

A 50 Hz cycle lasts 1/50 second, or 20 milliseconds. Direction reverses twice per cycle, so successive reversals are 10 milliseconds apart. Twenty milliseconds is a full cycle. Neither 1 second nor 50 milliseconds matches the half-cycle time.

Q10. The product of magnetic flux density, normal to a surface, and the surface’s area, is called the?

Show answer and explanation

Answer: C

Magnetic flux measures the total magnetic field passing through a given surface, calculated as flux density times the surface area.

Q11. Consider the following statements about Juno’s findings: 1. Juno found clusters of cyclones around both of Jupiter’s poles. 2. Juno showed Jupiter’s magnetic field matches a simple bar-magnet shape. 3. Juno’s gravity data suggest the zonal winds extend about 3,000 km deep. How many of the above statements are correct?

Show answer and explanation

Answer: C

Correct because statements 1 and 3 are right: cyclones ring both poles, and the winds run about 3,000 km deep. Statement 2 is wrong, since the field is stronger and lumpier than a simple bar magnet.

Q12. A fuse wire must be?

Show answer and explanation

Answer: A

A fuse must conduct current normally under safe conditions, but its low melting point lets it melt and break the circuit quickly once current becomes dangerously high.

Q13. A standard fuse wire is typically made from?

Show answer and explanation

Answer: B

Fuse wire is commonly a tin-lead alloy, chosen specifically for its combination of conductivity and a conveniently low melting point.

Q14. Which property of electric current specifically makes a fuse wire work?

Show answer and explanation

Answer: C

A fuse wire relies on the heating effect of current — when current exceeds a safe level, the wire heats up enough to melt, breaking the circuit.

Q15. A metallic wire’s resistance is?

Show answer and explanation

Answer: A

Resistance follows R = ρL/A — it rises with a longer wire, and falls with a thicker cross-section, for a fixed material.

Q16. Assertion (A): Bending a wire does not affect its electrical resistance. Reason (R): Resistance is proportional to a material’s resistivity. Which is correct?

Show answer and explanation

Answer: B

Bending leaves resistance unchanged, since the wire’s length, cross-sectional area, and resistivity all stay the same. But R, though a true general fact, doesn’t specifically explain why bending has no effect.

Q17. Which physical quantity does NOT affect the resistance of a cylindrical resistor?

Show answer and explanation

Answer: A

Resistance is a fixed property determined by a resistor’s length, cross-sectional area, and material resistivity — the current flowing through it doesn’t change that resistance value.

Q18. How does the internal resistance of a typical dry cell compare with that of an electrolytic cell?

Show answer and explanation

Answer: D

A dry cell’s paste-based electrolyte offers more resistance to current flow than a typical electrolytic cell’s liquid electrolyte does.

Q19. The reciprocal of electrical resistance is called?

Show answer and explanation

Answer: A

Conductance, the reciprocal of resistance, measures how easily a material lets current flow, and is measured in siemens.

Q20. Constantan, a material valued for its stable electrical resistance, is an alloy of copper and which other metal?

Show answer and explanation

Answer: C

Constantan is a copper-nickel alloy whose electrical resistance barely changes with temperature, a property exploited in precision resistors.

Q21. Metal-bodied electrical appliances use a three-pin connection, including an earth wire, mainly to?

Show answer and explanation

Answer: A

The earth wire gives stray current, from a fault inside the appliance, a safe path to ground, protecting the user from a dangerous shock through the metal casing.

Q22. Consider these statements: (I) a compass needle near a current-carrying wire gets deflected, and (II) a current-carrying wire creates a magnetic field around itself. Which is correct?

Show answer and explanation

Answer: A

A current-carrying wire generates its own magnetic field, exactly as Hans Christian Ørsted first discovered — and that field is precisely what deflects a nearby compass needle.

Q23. At fixed voltage, a uniform wire’s length is halved. Its material, temperature and area stay unchanged. How does its current change?

Show answer and explanation

Answer: D

Resistance is proportional to length under these conditions, so it halves. For an ohmic wire, I = V/R. At the same voltage, halving resistance doubles current. This ideal comparison neglects other circuit resistances and meter effects; stretching the wire would be a different change.

Q24. A uniform wire doubles in length at unchanged volume and resistivity. What happens to its resistance?

Show answer and explanation

Answer: D

Constant volume means that doubling length halves cross-sectional area. In R = ρl/A, both changes increase resistance. The combined factor is 2 ÷ 0.5 = 4. Doubling alone ignores the area change. Unchanged or halved resistance contradicts these stated conditions.

Q25. Three wires each of length L, cross-sectional area A and resistivity ρ are connected as shown (two wires of L, A connect X to Y in parallel, and a third wire of L, A connects Y to Z in series). These are to be replaced by a single wire of the same resistivity so that the resistance between X and Z does not change. If L1 is the length and A1 is the cross-sectional area of the new wire, which one of the following is correct? [NDA & NA (I) 2026, General Ability Test]

Show answer and explanation

Answer: A

The correct answer is (a) L1 = 3L and A1 = 2A. Each wire has resistance R = ρL/A, since all three wires are identical. Two wires connect X to Y in parallel, giving a combined resistance of R/2. The third wire connects Y to Z in series, adding resistance R. So the total resistance from X to Z is R/2 + R, which is 3R/2. The new single wire must match this: ρL1/A1 = (3/2)(ρL/A), so L1/A1 = 1.5 × (L/A). Option (a) fits: L1 = 3L and A1 = 2A gives L1/A1 = 1.5(L/A).

Beyond the answer

    Share your thoughts

    ✨Ask doubt
    ✨ Ask a Question AI×

    MCQ Question is an independent study site, not affiliated with any government body or exam authority. Official sources: UPSC upsc.gov.in · SSC ssc.gov.in · NCERT ncert.nic.in · PIB pib.gov.in

    WhatsApp support: +91 9319788829