MCQ Questions
🔍 Search
Menu

Heat and Thermodynamics Practice — MCQs with Answers (Set 3)

Practise 25 questions on Heat and Thermodynamics.

0 / 25 correct · click an option to check it

Q1. Regarding heat as a form of energy transfer, which statement is correct?

Show answer and explanation

Answer: A

Heat, specifically, is energy transferred because of a temperature difference. Energy can transfer other ways too, like mechanical work, without any temperature difference at all.

Q2. Which of these processes does NOT require any material medium to transfer heat?

Show answer and explanation

Answer: A

Radiation transfers heat as electromagnetic waves, which can travel through empty space. Conduction and convection both require matter, a medium, to carry heat at all.

Q3. What does heat mean in physics?

Show answer and explanation

Answer: D

Heat is energy transfer caused by a temperature difference. Temperature describes thermal state. Stored internal energy is a different quantity from heat transfer. Mass affects many heating calculations but is not itself heat.

Q4. In which of these does heat travel in a straight line at the speed of light?

Show answer and explanation

Answer: C

Thermal radiation travels as electromagnetic waves, moving in straight lines at the speed of light, unlike conduction and convection, which both depend on matter to carry heat.

Q5. Why does converting water to steam at 100°C need far more heat than melting the same mass of ice at 0°C?

Show answer and explanation

Answer: B

The correct answer is (b). Vaporization breaks far more molecular bonds than melting, so water’s latent heat of vaporization (≈ 2260 J/g) runs about seven times its latent heat of fusion (≈ 334 J/g).

Q6. A solid of mass m has temperature-dependent specific heat as C(T) = C₀ + αT, where C₀ and α are constants. The solid is heated from T₁ to T₂. Which one of the following is the correct expression for quantity of heat (Q) of the solid mass? [NDA & NA (I) 2026, GAT, Q53]

Show answer and explanation

Answer: D

Heat with a temperature-dependent specific heat needs integration, not simple multiplication.

Q = m ∫ C(T) dT, integrated from T1 to T2, where C(T) = C0 + αT.

Integrating gives Q = m[C0 T + αT²/2], evaluated at T2 minus at T1.

That expands to Q = m[C0(T2−T1) + (α/2)(T2²−T1²)].

Factor T2²−T1² as (T2−T1)(T2+T1), then pull out (T2−T1).

This gives Q = m(T2−T1)[C0 + (α/2)(T1+T2)]. Option (d) is correct.

Q7. A non-volatile solid solute may be separated from a solution by which of the following processes? I. Evaporation II. Crystallization [NDA & NA (I) 2026]

Show answer and explanation

Answer: C

The correct answer is (c) Both I and II. A non-volatile solute does not evaporate along with the solvent. In evaporation, the solvent is heated off, leaving the solid solute behind. Crystallization also removes the solvent, more slowly, giving pure crystals. Both methods work by removing the solvent, so both separate the solute.

Q8. For an ideal gas, a process is described by P = kT, where k is a constant. If the molar heat capacity for this process is C, then which one of the following is correct (where the symbols have their usual meanings)? [NDA & NA (I) 2026, GAT, Q55]

Show answer and explanation

Answer: B

For an ideal gas, PV = nRT. The process gives P = kT, so P/T stays constant. Combine the two: V = nRT/P = nR/k, a fixed number. So volume does not change here. A process at constant volume is called isochoric. Its molar heat capacity is Cv, by definition. So C = Cv, and option (b) is correct.

Q9. A diatomic ideal gas, such as oxygen, has 5 degrees of freedom near room temperature. What is its molar specific heat at constant volume, Cv?

Show answer and explanation

Answer: A

The correct answer is (5/2)R. Each degree of freedom contributes (1/2)R to Cv by the equipartition of energy, and a diatomic gas has 5 (3 translational plus 2 rotational). A monatomic gas, with only 3 degrees of freedom, has the smaller Cv of (3/2)R instead.

Q10. A reversible adiabatic ideal-gas expansion occurs with nearly constant heat capacities. What usually happens?

Show answer and explanation

Answer: D

Adiabatic means Q = 0. During expansion, the gas does work. Its internal energy and temperature therefore fall under these assumptions.

Sources: OpenStax thermodynamic processes; NASA ideal-gas processes.

Q11. The specific temperature to which a gas must be cooled before it can be liquefied through compression alone is called its?

Show answer and explanation

Answer: B

Above a gas’s critical temperature, no amount of pressure alone can force it to liquefy — it must first be cooled below this threshold.

Q12. The Curie point is the specific temperature at which?

Show answer and explanation

Answer: B

Above its Curie point, a ferromagnetic material like iron loses its strong magnetic ordering and becomes merely paramagnetic instead.

Q13. Assertion (A): To dilute concentrated sulphuric acid safely, acid is added slowly to water, never water added to acid. Reason (R): Water has an unusually high specific heat. Which is correct?

Show answer and explanation

Answer: A

Adding acid slowly into a large volume of water lets water’s high specific heat absorb the released heat gradually, preventing dangerous, sudden boiling or splattering.

Q14. A 5 g piece of ice at −20°C is put into m kg of water at 30°C temperature. The heat is exchanged only between the ice and the water. The final temperature of the mixture is 0°C in liquid phase. What is the value of m in kg? [NDA & NA (I) 2026, GAT]

Show answer and explanation

Answer: C

The ice must first warm up to 0°C, then melt fully, before the mixture settles at 0°C liquid. Heat to warm 5 g of ice by 20°C: 5 × 0.5 cal/g°C × 20 = 50 cal. Heat to melt that ice: 5 g × 80 cal/g (latent heat of fusion) = 400 cal. Total heat the ice needs is 450 cal, supplied entirely by the water cooling down. Water of mass 1000m grams cools from 30°C to 0°C, releasing 1000m × 1 × 30 = 30000m cal. Setting 30000m equal to 450 gives m = 0.015 kg. So option (c) is correct.

Q15. How much heat raises 0.50 kg of water by 10 K, using c = 4186 J/(kg·K)?

Show answer and explanation

Answer: B

Use Q = mcΔT. Multiplying 0.50 × 4186 × 10 gives 20,930 J. The other values use an incorrect mass or temperature factor.

Q16. A conductor carrying 1 ampere produces 2000 J of heat. If the current is doubled, how much heat is produced in the same time?

Show answer and explanation

Answer: C

Since heat is proportional to current squared, doubling the current quadruples the heat: 2000 J × 4 = 8000 J.

Q17. Which of these was the first synthetic, man-made plastic recognised as a poor conductor of heat?

Show answer and explanation

Answer: B

Bakelite’s early adoption as an electrical and thermal insulator made it historically significant as a heat-resistant synthetic plastic.

Q18. Which of these instruments is specifically used to detect radiant heat?

Show answer and explanation

Answer: D

A thermopile detects radiant heat directly, converting incoming thermal radiation into a small electrical voltage using junctions of dissimilar metals.

Q19. Which region of a flame is used by goldsmiths specifically to heat gold?

Show answer and explanation

Answer: B

The outermost flame zone achieves complete combustion and reaches the highest temperature, ideal for goldsmiths’ precision heating work.

Q20. The silvered (mirror-like) inner walls of a thermos flask specifically work to prevent heat loss by?

Show answer and explanation

Answer: D

A thermos flask’s silvered walls reflect radiant heat back rather than absorbing or emitting it, specifically minimising heat loss by radiation.

Q21. The statement that heat cannot spontaneously flow, by itself, from a colder body to a hotter one is a statement of the?

Show answer and explanation

Answer: C

This is the Clausius statement of the Second Law of Thermodynamics — heat naturally flows from hot to cold, never spontaneously the other way, without external work being done.

Q22. The direction in which heat flows between two bodies in contact depends on their?

Show answer and explanation

Answer: C

Heat always flows from the body at higher temperature to the body at lower temperature, regardless of their specific heat, latent heat, or contact area.

Q23. A liquid fails to wet the sides of a solid container if its angle of contact is?

Show answer and explanation

Answer: B

A liquid does not wet a solid’s surface when its angle of contact is obtuse (greater than 90°) — mercury on glass is a classic example.

Q24. While a solid is actively melting, its temperature?

Show answer and explanation

Answer: D

Like boiling, melting is a phase change at constant temperature. The heat added during melting goes toward breaking the solid’s structure, not raising its temperature, until melting finishes.

Q25. Regarding diffusion, consider: (I) liquids diffuse faster than solids, and (II) particles in a liquid move more freely, with more space between them, than particles in a solid. Which is correct?

Show answer and explanation

Answer: C

Both statements hold true — liquid particles move more freely and diffuse faster than the tightly packed, more restricted particles in a solid.

Beyond the answer

    Share your thoughts

    ✨Ask doubt
    ✨ Ask a Question AI×

    MCQ Question is an independent study site, not affiliated with any government body or exam authority. Official sources: UPSC upsc.gov.in · SSC ssc.gov.in · NCERT ncert.nic.in · PIB pib.gov.in

    WhatsApp support: +91 9319788829