Practise 23 questions on Mechanics Motion and Measurement.
0 / 23 correct · click an option to check it · +0 pts today
Q1. Regarding Young’s modulus and compressibility, which of these is correct?
Show answer and explanation
Answer: A
Young’s modulus carries the SI unit N/m², and a material’s compressibility is defined as the reciprocal of its bulk modulus.
Q2. What is the Young’s modulus of a perfectly rigid body?
Show answer and explanation
Answer: C
A perfectly rigid body has zero strain for any applied stress, making its Young’s modulus mathematically infinite.
Q3. In an experiment measuring a wire’s Young’s modulus, if the wire and the suspended mass are both doubled, what happens to the measured Young’s modulus?
Show answer and explanation
Answer: C
Young’s modulus is an intrinsic material property, unaffected by scaling up the wire or the suspended mass used to measure it.
Q4. Steel has a higher Young’s modulus than rubber. Under the same small tensile stress, which has less strain?
Show answer and explanation
Answer: B
Young’s modulus equals tensile stress divided by longitudinal strain. At the same stress, a larger modulus means less strain in the linear region. Steel therefore has less strain than rubber. Rubber can stretch much further, but that does not give rubber a higher Young’s modulus.
Source: Stress, strain and elastic modulus; Spring force and energy.
Q5. What is the modulus of rigidity of a liquid?
Show answer and explanation
Answer: A
A liquid’s modulus of rigidity is zero, since liquids cannot resist shearing stress — they simply flow instead.
Q6. Bulk modulus of elasticity is defined as?
Show answer and explanation
Answer: B
Bulk modulus is defined as the ratio of normal stress to volumetric strain within a material’s elastic limit.
Q7. Regarding elasticity across states of matter, which is correct?
Show answer and explanation
Answer: A
Solids are the most elastic and gases the least, precisely because gases compress far more easily than solids under the same applied stress.
Q8. Assertion: natural rubber has relatively poor elasticity. Reason: natural rubber has almost no cross-linkages between its polymer chains. How do these relate?
Show answer and explanation
Answer: D
Without cross-linkages between chains, unvulcanised natural rubber stretches poorly and lacks the elasticity that vulcanisation later provides.
Q9. Which elastic modulus describes a body’s resistance to uniform compression?
Show answer and explanation
Answer: C
Bulk modulus describes resistance to a change in volume under uniform pressure. Young’s modulus describes stretching or compression along one direction. Shear modulus describes resistance to a change in shape. A spring constant relates force to extension for a particular spring.
Source: Stress, strain and elastic modulus; Spring force and energy.
Q10. Assertion (A): Among alpha, beta, and gamma rays, alpha particles have the maximum penetrating power. Reason (R): Alpha particles are heavier than beta particles and gamma rays. Which is correct?
Show answer and explanation
Answer: D
Alpha particles actually have the LEAST penetrating power of the three, easily stopped by a sheet of paper, making Assertion A false. Reason R, however, is true — their comparatively large mass is precisely why they’re stopped so easily.
Q11. If alpha, beta, and gamma radiation all carry the same energy, their penetrating power in a given medium, ranked from least to most, runs?
Show answer and explanation
Answer: A
Alpha particles penetrate least, easily stopped by skin or paper. Beta particles go further, needing a few millimetres of metal to stop. Gamma rays penetrate the deepest, needing thick lead or concrete.
Q12. In the radioactive decay chain from thorium-232 down to lead-208, how many alpha and beta particles are respectively emitted?
Show answer and explanation
Answer: C
The mass drops by 24, requiring 6 alpha emissions (each cutting mass by 4). Those 6 alpha emissions alone would drop atomic number by 12, so 4 beta emissions are needed to bring it back up to the correct final value.
Q13. Beta particles, emitted during radioactive decay, are actually?
Show answer and explanation
Answer: B
Despite resembling ordinary electrons, beta particles are actually created and ejected from within the nucleus itself, during a neutron’s conversion into a proton — not the atom’s pre-existing orbital electrons.
Q14. Assertion (A): During beta decay, the recoiling daughter nucleus moves in the direction opposite to the emitted beta particle. Reason (R): Beta particles are not emitted with one single, fixed energy value. Which is correct?
Show answer and explanation
Answer: B
Both statements are true. But the opposite-direction recoil follows from momentum conservation, a separate fact from why beta particles are emitted across a continuous range of energies.
Q15. Assertion (A): The repulsive force between an atomic nucleus and an alpha particle follows an inverse-square law with distance. Reason (R): Rutherford performed the alpha-particle scattering experiment. Which is correct?
Show answer and explanation
Answer: B
Assertion A is true — this repulsion follows Coulomb’s inverse-square law. Reason R is also true historically, but it doesn’t explain WHY the force obeys that law; Coulomb’s Law itself is the actual explanation.
Q16. Ernest Rutherford’s famous alpha-particle scattering experiment, using a thin gold foil, revealed the presence of a?
Show answer and explanation
Answer: C
Most alpha particles passed straight through the gold foil, but a few bounced back sharply — evidence that an atom’s positive charge and mass are concentrated in a tiny, dense central nucleus.
Q17. The conservation of momentum during a collision between particles is best understood on the basis of?
Show answer and explanation
Answer: C
Momentum conservation in collisions follows from combining Newton’s Second Law (force equals rate of change of momentum) and Third Law (equal, opposite forces between colliding bodies).
Q18. What is the dimensional formula of velocity?
Show answer and explanation
Answer: A
Velocity’s dimensional formula is [LT⁻¹], involving only length and time, not mass.
Q19. What is the dimensional formula of momentum?
Show answer and explanation
Answer: B
Momentum’s dimensional formula is [MLT⁻¹], since momentum equals mass times velocity.
Q20. Which of these has a dimensional formula different from the other three?
Show answer and explanation
Answer: A
Power has different dimensions ([ML²T⁻³]) from Work, Torque, and Energy, which all share [ML²T⁻²].
Q21. Which dimensional formula describes pressure?
Show answer and explanation
Answer: B
Pressure is force divided by area. Therefore [P] = MLT⁻²/L² = ML⁻¹T⁻². The other formulas describe force, energy and momentum respectively.
Q22. What is the dimensional formula of angular velocity?
Show answer and explanation
Answer: A
Angular velocity has the dimensional formula M⁰L⁰T⁻¹, since it depends only on time, not mass or length.
Q23. Which pair of physical quantities share the same dimensional formula?
Show answer and explanation
Answer: C
Work and Energy share the identical dimensional formula, [ML²T⁻²], since both represent the capacity to do work.
Share your thoughts